What's new
New features, improvements and fixes at step2gcode – by date, in plain words.
To the G-code generator
15 November 2026
- New: New page "STL to G-code": mill 3D models (STL, 3MF, freeform STEP) on a CNC router – with roughing, finishing and cut-out.
- Improved: Tidier start page: the upload sits higher up, and the question about storing your settings comes after your first upload. What's new now has an address of its own.
- Improved: Very large SVG drawings: if a drawing is metres across, the page asks whether you meant pixels and scales it to 300 mm with one click.
- Improved: Circuit boards: if you upload the other side of a board as a separate file, the page explains how both sides count as one board – with alignment holes for turning it over.
- Fixed: Large drawings with many curves (e.g. a traced SVG): the toolpath view now shows the whole program instead of breaking off after part of it.
14 November 2026
- Improved: Mesh to STEP: if a mesh has holes, the page now says how many edges are broken and how to repair it in a few clicks – before you wait for a 3D run that cannot work.
- Improved: Cutter too short for the depth: the page now offers the smallest cutter that actually reaches, e.g. Ø2 mm instead of jumping straight to Ø6 mm.
13 November 2026
- Improved: Images: before the first job the page asks whether you use a laser or a milling machine – so your first program fits your machine.
- Improved: Sharing a subscription with your team? At the paywall the page now explains how a colleague passes the key on with a QR code.
- Fixed: 3D milling: large parts with freeform walls are no longer discarded after a long wait – the collision check now measures questionable spots on the exact part instead of on its approximation.
- Fixed: 3D milling: small, finely detailed parts no longer run out of time while finishing – if time gets short, the finishing rows are placed a little further apart and you still get your program.
12 November 2026
- New: PCB milling: if the layers in a Gerber ZIP are not recognised by their file names, you can now say which file is the copper layer and which the outline, instead of getting an error.
- Improved: 3D milling: a very small step-down that the calculation cannot handle is reported straight away, with the step-down that works – no more waiting minutes for an error.
- Improved: DXF and SVG: with a cutting depth of 0 mm the page now asks for the depth before starting, instead of calculating an empty program.
- Improved: Layout window: an image put in by mistake now says where it belongs – close the window and upload the image directly, it is engraved on its own.
11 November 2026
- Improved: 3D milling: large parts and parts from STL files that used to stop at the time limit now get their program – mesh files are read much faster, and when time runs short the finishing rows run a little wider apart.
- Fixed: Sliced print files (.gcode.3mf from Bambu Studio or OrcaSlicer) hold no model. The page now says so and how to export the model as STL or 3MF, instead of offering a 3D button that could not work.
10 November 2026
- Improved: Buying credits: the dialog and the payment page now say plainly what you get, and the payment page opens in your browser language where available.
- Improved: Narrow pockets: the offer of a separate program now shows the time at the machine, compared with milling the whole part with the small cutter.
- Improved: Layouts: if a part needs 3D milling, the message now says what to do. Remove it from the layout and upload it on its own, then it can be milled in 3D.
9 November 2026
- Improved: Your picture stays: if the page reloads, for example on a phone, the uploaded image and its settings come back in the same tab.
- Fixed: 3D milling from very fine meshes (over 30,000 triangles): closed STL and 3MF files were wrongly refused as "not closed". They are now calculated.
8 November 2026
- Fixed: PCB upload: a ZIP without Gerber files now says what it holds instead of "copper layer missing" – a KiCad project gets the menu path for the Gerber export, an STL or OBJ the hint to upload the mesh on its own. SVG files with a long comment or header before the drawing are no longer refused as invalid. A double click on a credit package no longer opens two payment pages.
7 November 2026
- New: Parts that are too big: a long part standing on end can now be laid flat with one click, and a part too large for 3D milling can be scaled to a size that fits, if you want that.
- Fixed: Hollow sections: a box section no longer gets just a rectangle around it. A cavity that neither side can reach now leads to the 3D offer, with a clear note on what can be milled.
- Improved: V-bit engraving of a DXF or SVG now starts on the fast 2D path right away, so drawings with curves no longer fail first.
- Improved: Holes and pockets programs: the main program and the extra program now sit side by side, with a note if one has not been downloaded yet. The buy dialog says when your free model is still there.
- Fixed: 3D milling: solid parts no longer get the false note that some material is reachable from no side.
- Fixed: 3D milling: a STEP file with an open triangle mesh, for example from Onshape, now gets a real answer: the openings are closed and the part is calculated. If a ZIP holds a drawing instead of PCB files, the page says which file to upload on its own.
6 November 2026
- Fixed: Layout: if a part does not fit on the sheet, the page now tells you how large it is and enlarges the sheet with one click. Lines outside the sheet are pointed out.
5 November 2026
- New: Layout: a drawing with a frame or several parts can now be split with one tap, and the parts are arranged one by one. If a part does not fit, the page names exactly what it needs.
- Improved: Subscriptions: the page now warns before the monthly models run out, says when they start anew and asks before using credits.
- Improved: Buying is simpler: packages and plans can be chosen straight away, and you confirm the immediate start in the secure Stripe checkout.
- Improved: Working on a second device? If a download is refused, you can now enter your existing access key right at the top.
- Fixed: PCB: uploading a ZIP of finished programs now tells you that it needs the Gerber export.
- New: Facing for DXF and SVG in seconds: the fast 2D path now faces the plate first and then cuts every opening and the outline below it – also when you enter a stock height. Engraving mode cannot face and now says so instead of silently leaving it out.
- Improved: If a drawing has no inner contours, the page now says so as soon as you pick "inner contour only" – with a button to use the outer contour instead of an empty program.
- Improved: Outlines made of very many short lines (common in traced drawings) now calculate about six times faster when inner contours are chosen. A layout that takes too long now tells you which part it was and what helps.
4 November 2026
- Improved: 3D milling says sooner when a part is too deep for any cutter – in seconds instead of minutes – and asks first when a file looks like an assembly of many parts.
- Improved: PCBs: large boards now show how long they have been calculating, and cancelling really stops the calculation.
- Improved: PCB: after one side is done, a single click now generates both sides together – with two alignment holes, so the bottom lines up after turning the board over.
3 November 2026
- New: New guide: recreate a part from photos on graph paper or from an STL file with an AI agent (Claude, ChatGPT) driving FreeCAD, Fusion or SolidCraft – an editable STEP file, ready to mill.
- Fixed: Stock height: with a cutting depth entered (pockets only, say), the stock is now compared with the part’s height – before, the program could face off too much at the top.
- New: Pockets with a cutter of their own: set a smaller cutter for the pockets, and you get two programs – everything else with the main cutter, then every pocket with the small one. One model, one credit.
- New: Under “Post-processor” you can now look at a sample program for your controller – header, tool change and arcs, without computing your part first.
- Improved: If a pocket is missing because it is too narrow for the cutter, the download asks once whether to add the pockets program.
- Fixed: “Your recent programs” now only lists what can still be downloaded.
- Fixed: A very large picture (well over 100 megapixels) is no longer reported as "could not be read" – the page now says how large it is and that it needs to be scaled down.
- Improved: A 3D part that is too deep even in two setups now gets a clear answer instead of the advice to use two setups – with assemblies: upload each part on its own.
2 November 2026
- New: DXF and SVG drawings are now cut out much faster – usually within seconds, parts to size, with holding tabs. Under milling options you can switch back to the classic way for a job.
- Fixed: Uploading a whole kit at once works now – several hundred parts in one go are no longer turned away.
- Improved: A tiny part whose openings do not fit the cutter now offers to read the drawing in centimetres or inches – often it was simply drawn in another unit.
- Fixed: Milling an STL or 3MF as a 3D part: the 3D view now shows the model while the program is still being computed, instead of an error.
- Fixed: Files with "preview" in their name (for example "card_preview.webp") no longer end in "Upload session expired" when you generate.
- Improved: If openings are narrower than the cutter, the result now offers a button to recompute with a smaller cutter right away.
1 November 2026
- Improved: Mesh to STEP: "sharp edges" now also works on parts with a cross bore – and if it does not work for a part, you get the solid with recognised faces instead of no file.
- Improved: Large 3D parts: the finishing pass no longer gets left out at the edge of big parts, and steep walls on large parts are finished more often – more coarsely if time is short – instead of being left out.
- Fixed: 3D milling in two setups: side 2 now cuts the part free with holding tabs – it no longer comes loose in the last pass.
- New: Subscription: switch between Maker and Workshop at any time – the difference is prorated.
- Fixed: On the English page, the notes about openings or outlines that could not be cut out are now in English too – including the tip to try a smaller cutter.
31 October 2026
- New: 3D milling straight from STL and 3MF: if a mesh cannot become an exact solid, it can now be milled as a 3D part as it is – no detour through another CAD program.
- Improved: 3D milling now uses your step-down and cutting length – or the material table, matched to the end mill it picks. Before, it always roughed 2 mm deep.
- Improved: 3D milling now follows the same settings as 2.5D: your post-processor (every controller except Heidenhain), your own program start and end, holding tab size, zero on the spoilboard and ramp entry.
- Improved: 3D milling: STEP files that hold only a triangle mesh (for example from Onshape after importing an STL) are now milled instead of being refused with "no solid".
- Fixed: 3D milling: the last result notes that were still in German on the English page are now translated.
30 October 2026
- New: New option "One file per step": the download then holds one program each for facing, pockets, holes, inner contours and finally the outer contour – mill them one after the other from a single run.
- New: Arranging parts: each part now has a material thickness (from the STEP part or the file name, e.g. "_6mm"). Different thicknesses get a sheet each, one after the other, with the right depth.
- New: 3D milling: the part is now cut out at the end with holding tabs, like a 2.5D outer contour – it no longer comes loose while finishing.
- New: New field "Stock height": if your raw block is higher than the part, the difference is faced off first – for 2.5D and 3D.
- Fixed: 3D milling: the download now holds one program per tool – roughing and finishing separately, with a note to change the tool and zero Z. Machines without a tool changer no longer run on with the wrong cutter.
- New: New: a subscription for regular milling – Maker with 40 models a month or Workshop with API access, monthly or yearly, cancel at any time. Credits stay as they are, no subscription needed.
- Improved: DXF drawing much too large (over 2 m)? The page now offers to read it in a smaller unit and shows the size that results.
- New: Mesh to STEP: new option to turn small fillets into sharp edges – a clean solid with real faces only (beta).
- Improved: Shorter warning lists: when many pockets are too narrow for the cutter, you now get one line with their numbers and widths instead of one line per pocket.
- Fixed: Arranging many parts: if you add more files at once than the server accepts in 10 minutes, the window now stops and tells you how many parts are loaded and which ones to add later.
29 October 2026
- Improved: Mesh to STEP: CAD parts that cannot be rebuilt exactly now get real planes and cylinders wherever they fit, instead of a body made only of triangles.
- Fixed: 3D milling: the roughing pass could skip whole sides of a part. It now clears all around before finishing.
- Improved: Is your cutter too short for the depth? One tap computes the part with a sturdier cutter and the narrow pockets as a program of their own. And the offer for narrow pockets now stands above the warnings.
- Fixed: STEP files with many separate parts far apart no longer run out of time before the program even starts.
25 October 2026
- Fixed: Laser: if you chose a 3D printer with a laser module (Marlin) and briefly switched to milling and back, the page now keeps Marlin instead of quietly going back to GRBL with the wrong power scale.
23 October 2026
- Fixed: 3D programs are no longer thrown away right at the end because the final check ran out of time.
- Improved: When your program is ready while you are in another tab, the tab title now says so.
- Improved: STEP and DXF files may now be up to 20 MB instead of 5 MB.
- Improved: Picture too large for one program? The page now offers the largest width that fits – one tap.
- Fixed: If a program comes out empty, the page now says why – for example when the openings are narrower than the cutter.
- Improved: We now ask for your rating after you have tried the program on your machine, not right after the download.
- Improved: A corrected version of a file you just downloaded is free for an hour – fix a line, upload again, download again.
- New: New pages explaining DXF to G-code and SVG to G-code – what the check looks at, what to watch out for, and the most common questions.
- Fixed: SVG files are milled much faster, and openings made only of curves are no longer left out.
- Improved: Picture milling: if Marlin (3D printer) is still selected from the laser, the page now says so and switches to GRBL with one tap.
- Improved: Image milled instead of lasered? The hint now names the tool and stands out, with a button to switch to the laser.
- Improved: Clearer wording for the tick box before buying credits – it now says plainly why it is needed.
- Fixed: Laser: switching from Marlin back to GRBL now also resets the power scale to 1000 – before, the program could burn at a quarter of the power.
22 October 2026
- Fixed: Layouts now cost only the parts that are actually on the sheet – parts that did not fit are no longer counted.
- New: Parts did not fit on the sheet? One tap enlarges the sheet, or takes this sheet and keeps the rest for the next one.
21 October 2026
- Improved: A drawing without a single closed outline is now named before you generate – and switched to engraving on the lines, instead of failing twice.
20 October 2026
- Improved: Engraving pictures on a 3D printer with a laser module: choose the machine right above the preview. For printers the origin goes to the front left corner, nothing moves below 0, and the page warns when a program has more moves than a printer keeps up with.
- New: Closed the page during a 3D calculation? If you allowed settings to be kept in your browser, the finished program is waiting on your next visit.
- Improved: When a smaller cutter would be too short for the whole part, the page no longer offers to recompute everything with it – it suggests a separate program for the narrow spots instead.
- New: If a new version of the page comes out while your tab is open, you now get a hint to reload it.
- Fixed: 3MF files saved by a slicer (Bambu Studio, Orca, PrusaSlicer) can now be turned into STEP – they used to be turned away as "empty".
19 October 2026
- Fixed: Fixed: in drawings with many openings close together (e.g. mandalas), some openings could be missing from the program without a word. Now every opening is milled – and should one ever be left out, the page says so.
- Improved: Parts narrower than your cutter are now named before you generate – with a button for a cutter that fits. And messages for SVG files now say SVG.
- Fixed: Laser engraving now also works for pictures whose file name is written in Cyrillic or another non-Latin script, or is very long – such pictures used to stop with an error.
18 October 2026
- New: Downloading several parts one by one? The page now points you to the layout: all parts on one sheet, one program, the same price per part.
- Improved: Drawings with many contours are now cut out to size again instead of being switched to engraving on the line – the calculation may just take a few minutes.
17 October 2026
- New: Pockets too narrow for your cutter now get a program of their own, milled with a cutter that fits – your main program stays as it is. And pockets that were left out are now named instead of silently skipped.
- Fixed: Pocket narrower than your cutter? The warning now gives the gap to a hundredth of a millimetre – no more "6 mm wide, cutter 6 mm".
16 October 2026
- Improved: Is your cutter far too short for the depth of the part? You now learn it right away – with the depth, the passes and the hours it would take – and one tap recomputes with a 6 mm cutter.
- Improved: Is a STEP file too tall because it holds several parts? The message now says how many bodies it contains and suggests uploading just the part you want to mill.
- Fixed: 3D milling no longer stops without a reason when a STEP file contains a damaged face – it computes a little coarser and tells you so.
15 October 2026
- Improved: Bought credits at the download? When you come back from the payment, your finished program is still there – one tap on download, no need to generate it again.
14 October 2026
- Improved: If a drawing comes out smaller than your cutter, buttons below the warning read it as centimetres or inches and recompute – showing the size it would have.
- Improved: Is a DXF drawing smaller than your cutter? You now see it right next to the drawing unit, before generating, together with its size in cm and inches.
13 October 2026
- New: The laser now also cuts STEP parts in a nesting layout – their outline and every opening that goes through, never a pocket.
- New: Your last downloaded programs now wait above the upload for 24 hours – download them again with one tap, free of charge. Only in your browser and only if you allowed saving settings there.
- Improved: A part far too long (over 5 m) now gets the unit hint within seconds instead of after minutes. A part that is too thick offers to enter a milling depth right away.
- Fixed: A STEP file that only contains a triangle mesh now gets a clear tip: convert the mesh with “STL to STEP” – exporting again the same way does not help.
12 October 2026
- Improved: Nesting now counts each part as a model of its own: parts you already have stay free, new ones cost one credit each (your free model covers one). A part paid for stays free – alone and in every later layout, so rearranging costs nothing.
- Improved: On the German page, materials and a few settings now have German names.
- Improved: The “PRO” labels are gone: every function is included for every model – you pay per model, not per feature.
- Fixed: In 3D milling, a part whose surfaces are too complex to compute now gets a clear answer within seconds instead of an abort after more than a minute – with the tip that helps most often.
- Fixed: Fixed a rare case where the page went blank in the milling settings when it did not recognise the stored material – it now falls back to wood.
- Fixed: The picture preview no longer shows an error while you type a new laser power or speed – it waits until the number is complete.
11 October 2026
- Improved: The credit packages now come first when you top up – the explanation follows below.
- New: Holes too narrow for your cutter can now get a program of their own – milled with a smaller cutter, drilled, or only spotted. The main program keeps its cutter and stays fast.
- Fixed: The holes program now also contains small holes in the floor of a pocket – before, they were offered but missing from the file.
- Fixed: If every hole of a part is narrower than your cutter, the page now says so – with the hole size and a button to recompute with a cutter that fits. Before, it only said there was nothing to mill.
- Fixed: Chamfer or engraving that finds nothing to cut now says why instead of reporting an error, and facing that cannot be computed is pointed out.
10 October 2026
- Improved: Large parts (from 400 mm or with very many faces) may now compute for up to 10 minutes when the server has room – instead of stopping after 3 minutes. Holding tabs are also computed faster.
- Improved: 3D milling: the page now says how long a 3D program usually takes (1 to 6 minutes) and shows a clock while it runs – keep the page open until it is done.
- Improved: If downloading a model costs a credit, it now says so right under the Generate button – before you start, not only at the download.
- Improved: SVG files with lettering: the page now says right after the upload that text is not milled and how to convert it to paths – before, the lettering was simply missing from the program.
9 October 2026
- Improved: Large plates with many pockets – such as a foam insert for a tool drawer – are computed more than twice as fast.
- Improved: Two-sided boards: after the top side, the page offers the bottom side from the same upload – it stays the same board.
- Improved: Arranging parts on a sheet that you have already downloaded or paid for is free – no new model.
- Improved: STEP parts with straight walls are computed faster.
- Fixed: Tiny parts closer to the main part than the cutter is wide are left out and named, instead of cutting into the main part – a plate with such parts no longer runs into the time limit.
- Improved: A whole drawing sheet (frame, dimensions, title block) is recognised – you are asked to export only the outline of the part.
- Improved: New warning when the depth per pass is far above the cutter diameter (e.g. 13 mm in one pass with a 6 mm cutter) – such a pass breaks the cutter easily.
8 October 2026
- Improved: Laser cutting: holes and inner parts are now cut before the outline around them – the part no longer comes loose too early.
- New: DXF: choose the unit of your drawing (mm, cm or inch) – a drawing marked with the wrong unit no longer comes out many times too large.
- Improved: An empty DXF (or one with only text) is reported right after the upload, not after generating.
- Improved: Drawings that are better engraved: one tap switches to engraving and generates right away.
- Fixed: STEP files made of triangles (e.g. from STL to STEP) now go straight to 3D milling instead of running into the time limit.
- Fixed: DXF drawings from plotter and converter programs that store every line as a "3D polyline" (all at the same height) are now milled, engraved and lasered – they used to be refused as 3D toolpaths.
- Improved: Board drawings exported as DXF from EasyEDA (PCB_…_date.dxf) now get the hint that the Gerber ZIP path mills isolation, holes and outline directly.
- Fixed: The full-screen button of the 3D viewer no longer gets stuck – one click always closes the full view.
7 October 2026
- New: STL to STEP: choose the unit of your STL file (mm, cm, m or inch) – an STL saved in metres no longer turns into a tiny part.
- Improved: 3D milling on two sides: the page reminds you to download side 1 before you generate and mill side 2.
- Improved: Pictures on the phone: the preview now stays in view while you change the method or the settings below it.
- Fixed: The price shown before generating was sometimes "1 credit" for a model you had already paid for – it now says correctly that it is free.
- Fixed: STEP files that hold only loose triangles instead of a solid no longer run into the time limit – you get the outline program and a note why.
- Fixed: Drawings in which every outline lies twice on top of itself (exported twice by mistake) now get their program in seconds – they used to run until the time limit.
- Fixed: With cookies blocked for this site, the page now works anyway – it simply forgets your settings when you reload.
- Improved: Mesh to STEP: if an STL is smaller than a millimetre, the page now says it was probably exported in metres – before you download it.
6 October 2026
- Improved: If something on the page goes wrong, you now get a clear message instead of a blank page – and after reloading, your last program is offered again. If only the 3D view fails, the rest of the page and your download stay.
- New: New hint: if the cut is deeper than your cutter can reach, the page says so – with the flute length you entered, or the usual one for that diameter.
- Fixed: If your browser translates the page, it no longer turns blank when you click "Generate G-Code" – your result appears as usual.
5 October 2026
- Fixed: STEP files in the newer AP242 format from Onshape or CATIA could come out a few millimetres off – the toolpaths now sit exactly where the part is.
- New: Did your program work on the machine? On your next visit after a download, the page asks once – your answer helps make the toolpaths better. Only if you allowed saving settings in the browser.
- Fixed: Large laser and engraving drawings with thousands of shapes are ready in well under a minute. Before, a drawing with about 5,000 shapes could run into the time limit and deliver nothing.
- Improved: A short network hiccup no longer frees the generate button while your job is still running – no more accidental second run. Large laser drawings are also put in cutting order faster, and if your free model is used up, the page says before generating that generating and the preview stay free.
4 October 2026
- Fixed: Small parts with a finely traced outline – such as shapes traced from a picture – get their outer contour again. Before, the cut-out of the largest part could be missing.
- Fixed: 3D milling: the tip for a sturdier tool only suggests tools you can choose (up to 12 mm). Before, the button could offer a 16 mm ball end mill and then fail.
- Improved: If a detailed drawing is switched to engraving because the normal way takes too long, the page now says plainly that this engraves on the lines and does not cut parts out to size.
- Improved: More SVG files are accepted – compressed ones, UTF-16 ones, and pictures that were saved with the .svg ending go the picture path. Very long parts, parts narrower than the cutter and jobs with hundreds of passes now get a hint before you mill.
3 October 2026
- New: Bought on your phone, working on your PC? In the credits window, “Use on another device” shows a QR code and a link that carries your credits across – no more typing the token. On the invoice the token now stands on a line of its own.
- Improved: Clearer messages: a file that is too large comes with tips to make it smaller, and if the free model was already used on another device in the same network, the page says so.
- Fixed: STEP files that contain only surfaces and no solid body – some CAD programs export them that way – now get their outer contour. Before, the program could be missing the cut-out.
- Fixed: The quick check of DXF drawings after uploading works again for all files – including the advice to engrave very detailed drawings directly instead of waiting for a time-out.
- Fixed: If you type in your token on a second device and it is not recognised – for example because it was not copied completely – you now get a clear message instead of an empty field.
2 October 2026
- Improved: Your first model is free – with every feature and without an account. This replaces the one free model per month: if you already had a free model, further models are downloaded with credits, and every model paid for stays free for good.
- Fixed: Parts lying inside the hole of another part – such as rings around one centre or a disc in a cut-out – are now milled. Before, they could go missing in DXF and SVG drawings, and in STEP files the hole around them was left out.
- Fixed: If a file cannot be uploaded, you now see why – for example an SVG that contains only text or a file that is too large – instead of just "Upload failed".
- Improved: Fewer dead ends: an SVG that only holds a picture is now handled as a picture, an isolation drawing of a circuit board gets fine engraving set up at a tap, several copies of the same part stacked into each other are milled once, and after a time-out the page says what to change.
1 October 2026
- Improved: Easier when something needs attention: warnings now say in plain words what to do, often with a button to recompute with a fitting cutter. A missing milling depth is asked right where the message appears, circuit board layers point to the board path, and your last program is still there after reloading the page.
- Improved: 3D milling (beta): if a single finishing pass fails the check against the part, you now get the program without that pass and a clear note - instead of no program at all.
- Fixed: A part that is smaller than a millimetre (usually exported in metres) now gets a clear note about the unit and its intended size, instead of an empty program.
30 September 2026
- Improved: 3D milling (beta): if your part is recognised as 3D, the 3D program now starts by itself - no extra click.
- Improved: 3D milling (beta): tools are now chosen automatically by depth - larger by default, so the calculation and the milling are faster. You can still pick the ball end mill yourself. If a part is so deep that a tool would need an unusually long cutter, the result suggests a sturdier one and recomputes with it at a tap.
29 September 2026
- New: Laser: a drawing with black and coloured lines can now be cut and engraved in one program – black is cut, colour engraved, both exactly aligned. The page also suggests the original size stored in the image and offers a free material test card to find power and speed in one run.
- New: Circuit boards: fewer drill changes. Enter the drills you own, or let similar hole sizes share a drill; large holes can be milled with the cut-out end mill. Every enlarged hole is checked so that it does not cut a neighbouring track or leave too little copper round it.
- Improved: 3D milling (beta): large parts up to about 1.8 m now get a program. If the chosen cutters are too small for the part, the calculation picks suitable ones and tells you which to use.
- Fixed: V-carving: logos and lettering without a frame are now carved completely. The new "Automatic" contour selection checks whether the drawing has a frame, and thin letters are no longer left out.
- Fixed: 3D milling: large flat parts are no longer stood on edge when that needs a far longer tool than lying flat. The viewer shows the part while the tool paths are being calculated. If a part is too large for the chosen tools, the message now says why and which tool size works.
- Improved: Circuit boards: the programs now appear in the tool path viewer, each one can be shown or hidden. The preview draws the isolation paths visibly and opens full size on tap. EasyEDA board outlines are recognised correctly.
- Improved: Reworked cutting values for all materials: gentler depths per pass for hobby machines (aluminium 0.6 mm instead of 2.4 mm with a 6 mm end mill), feeds that suit small end mills better. Values you entered yourself stay.
- Improved: Nesting downloads now carry the names of their parts instead of always being called nested.nc.
- Fixed: Feeds now follow the material table and adjust whenever you change the tool diameter – small end mills no longer run with the feed meant for a 6 mm tool.
- Improved: 3D finishing now runs the ball end mill with its own speed and feed: slower feed to match its smaller size, higher spindle speed - never above the new "max. spindle speed" setting for your machine.
28 September 2026
- New: Circuit boards: now both sides with alignment holes for turning the board over, optional clearing of all unused copper, and programs for GRBL, LinuxCNC, Mach3 or Marlin.
- New: Viewer: show or hide single operations - handy with 3D milling, where roughing and finishing lie on top of each other.
- New: New: mill circuit boards. Upload the Gerber export from KiCad, Eagle or EasyEDA as a ZIP and get one program per tool: isolate the traces, drill the holes, cut out the board. With a preview and a warning where traces sit too close for the tool.
- New: 3D milling (beta): parts with freeform surfaces – organic shapes, fillets, reliefs – now get a 3D program instead of a refusal. Roughing with an end mill, finishing with a ball end mill, and every program is checked against the part before you get it. Where one side is not enough, you get a second setup on request. 2.5D milling for flat parts stays the proven path; 3D is new, so please look at the result closely in the viewer.
- Fixed: Pockets that open out at the edge of the part are now cut all the way through that edge: the cutter runs slightly past it, so no thin sliver is left standing along the open side.
- Fixed: Parts with a dome or other large spherical surface are now recognised as 3D parts. Before, they could slip through as flat parts and got a program that left the dome uncut. Small rounded corners are still milled as usual.
27 September 2026
- Fixed: Openings with free-form outlines – the cut-outs of a logo, for instance – are milled again. Where their edges ran in opposite directions, the openings were missing from the program without any warning.
- Fixed: Parts that lie on their side in the STEP file and have free-form outlines – a logo cut from a plate, for instance – are no longer mistaken for 3D models. They are turned flat and milled like any plate.
- New: Is your drawing a set of parts or a plate with cut-outs? Where both readings fit, the check after uploading now asks – and suggests the likelier one. Parts on a sheet keep their size, and holes drawn without their plate are milled as holes.
26 September 2026
- Fixed: Drawings with several identical parts – six equal holes, ten equal washers – are now machined completely. Before, only one of them got a toolpath.
- Fixed: Older DXF files (e.g. from R12 exports or Inkscape) now keep their arcs: rounded corners stay round, and small circles and holes are no longer lost.
- Improved: A STEP file that holds only a sketch can now be milled – just enter the cutting depth. Empty STEP exports now get a clear hint instead of a wrong "3D model" message.
- Improved: An image uploaded in milling mode now stays there and is milled. Want to laser it instead? One click in the image panel switches over.
- Improved: Easier to use on the phone: larger buttons and links, the upload is visible right away, and the page tells you what one model costs.
- New: The milling know-how articles now have their own English pages, and every page answers the most common questions right below the tool.
- Improved: The image preview now shows the running time for the speed you set – change the feed and the minutes update right away.
- New: Images can now be milled too: engrave an outline, centerline or photo edges with a V-bit or end mill – set the engraving depth just like for a DXF file.
- New: Faster laser engraving from images: instead of row by row, the laser can now follow lines – as an outline, along the middle of each stroke, or as a line drawing made from a photo. Often many times faster; the preview shows the running time.
25 September 2026
- New: Laser-engrave photos and logos: upload a PNG, JPG or WebP like any other file, choose photo, logo or grayscale, set the size in millimetres – the preview shows what the laser will burn before you download.
- New: Laser G-code for Marlin: 3D printers with a laser module now get their own program (vector and image engraving), not just GRBL.
- New: STL and 3MF files now go straight to G-code: drop the mesh on the upload and it is rebuilt into a STEP body on the spot, checked against your mesh, and then treated like any STEP file. The STEP file can be downloaded too, and G-code plus STEP from the same mesh count as one model. Unsupported files now get a clear message instead of vanishing.
- Fixed: The site stays fast while a large drawing is being checked. Before, one very large DXF file could keep the whole site from loading for a few minutes. Checking large drawings is also much quicker now.
24 September 2026
- Fixed: Important for Centroid, Dynapath, EstlCAM, Fanuc, Philips, RepRapFirmware, Smoothieware and UCCNC: programs for these controls did not switch the spindle on. They now contain the tool change and the spindle start with your speed. If you downloaded a program for one of these controls before, please generate it again.
- Fixed: Heidenhain output works again: programs for Heidenhain controls came out empty or broke off. They now contain the full toolpath, the tool call with spindle speed and the correct feed rate. Please simulate the first program on your control before running it.
- Fixed: Files with several parts: when the outer contour of a single part could not be computed, it is now calculated a second way – in our test, an assembly of ten parts got all ten outlines instead of three. If it still fails, the result says so clearly.
23 September 2026
- Fixed: Some parts used to stop without a program and without a reason while the outer contour was being computed – they now get their program. If an outer contour really cannot be computed, the result now says so clearly instead of leaving it out silently. And if a file ran out of time, starting it again unchanged gives you the answer at once instead of another three-minute wait.
- Improved: Very detailed DXF drawings – traced images with thousands of tiny segments – are now smoothed within 0.05 mm before milling, so more of them get a program. If a drawing still takes too long, 2D Direct Mode is switched on for you right away – just start again.
- Fixed: More DXF drawings work: when the drawing sits in blocks – as in our own nesting export – in a paper-space layout, in mirrored blocks, or the file is slightly damaged, it is now read and milled. And if a DXF contains no lines at all, the message says why: only text, a 3D solid, a mesh or nothing.
- Improved: STEP parts with many holes, pockets or faces are prepared much faster. Many parts that used to stop after three minutes with "too complex" now get a program – and the program itself is exactly the same as before, only it arrives.
- Improved: A part exported in the wrong unit – say 30 metres instead of 30 millimetres – now gets a clear message within seconds, naming its size and pointing at the unit. Until now it ran for three minutes and ended with "too complex".
- Fixed: Holding tabs can now be switched off through the API (REST and MCP). Until now they were added anyway. Nothing changes on this website.
22 September 2026
- Fixed: Some STEP parts used to run for minutes and then end with no file and no usable message. Two causes are fixed: a rounded cylinder whose seam confused the hole detection, and surface types the program could not read at all. Parts that used to come back empty now produce G-code – and where a part really is not millable in 2.5D, you now get the clear message instead of a crash.
14 September 2026
- Improved: First purchase bonus now on every package: 40 credits for €19.90 instead of 30, and 125 credits for €49.90 instead of 100. The larger the package, the lower the price per model.
12 September 2026
- Fixed: DXF drawings with many contours - lettering and signs above all - no longer run into the time limit. One customer file used to stop after three minutes with nothing to show; it now finishes in half a minute. Nothing changes for STEP files.
- Fixed: A program with no cutting moves is no longer reported as success. If you pick only "inner contour" and the drawing has none, you now get a clear message instead of an empty file – the kind of mistake that used to surface at the machine.
- Improved: The advice after a timeout now fits the file. Drawings made purely of polylines no longer get told to convert their splines – there are none – but are pointed at the number of contours instead.
9 September 2026
- Fixed: The page no longer scrolls sideways on a phone. Once a file was loaded, the settings pushed the layout about 110 px past the screen edge, so you had to drag the page left and right to reach the right-hand controls. Everything now wraps within the screen.
- Fixed: Laser: the first contour is now cut. The program switched the laser on with a line GRBL rejected, so the first shape was traced with the beam off – and some senders aborted the whole job. Fixed. If you have laser files from before today, generate them again.
- New: Laser: you can now set your machine's S-value maximum (GRBL $30 – usually 1000, but many diode lasers run 255). If it does not match, 80 % power silently becomes full power. The generated file also names the settings your machine needs ($32=1, $30).
- Improved: The program now says which tool it was cut with: when you pick a V-bit, the header says "V-Bit 60deg D6mm" and the file name carries VBit60deg-D6mm. Until now a pointed V-bit was listed as an end mill, and the angle - the thing that actually describes the cutter - was nowhere in the file. The toolpath itself is unchanged.
- Improved: The stl2step page now says plainly what it is best at: 2.5D parts that were designed in CAD and only ever published as STL or 3MF - the brackets, adapters, lids and mounts from sites like Printables or Thingiverse, where no STEP file exists any more. Those consist of exactly the shapes that can be recovered, so a printable model becomes a solid you can dimension, adapt and machine.
- Fixed: The V-bit no longer stays behind: it belongs to 2D direct mode, so as soon as that mode is off – undone, switched off or simply the next file – the end mill is back, which is the tool that cuts a contour with tool compensation. This now holds after reloading the page as well.
8 September 2026
- New: stl2step now has a "Report a bug" button - in the footer and right next to a refusal, a failed build or a deviation the check flagged. The finding is filled in for you, and the mesh you uploaded can go along with it, which is usually the only thing we need to find the cause.
- New: After downloading a STEP file we ask, in two questions, how the conversion went. The rating counts separately from the G-code service - so we can see which of the two actually earned its stars.
7 September 2026
- Improved: When the pre-check switches to 2D direct mode (engraving), the tool now switches to the V-bit along with it – and back to the end mill on the next file that does not need the direct mode. Your own choice of tool is never overridden.
- Fixed: Fixed: engraving and V-shape Adaptive could end up switched on at the same time. They exclude each other now wherever the direct mode is turned on.
- New: stl2step turns away far fewer files: when a part cannot be rebuilt exactly – a freeform surface, or a mesh that falls into too many pieces – you now get a transferred solid instead of a refusal, marked as such and with the deviation measured and stated. Three of our own test parts that used to come back empty now deliver a file.
- Fixed: Fixed: the 3D view at stl2step stayed too large after leaving fullscreen. It now returns to exactly the size it had before.
6 September 2026
- New: stl2step now tries to win real surfaces back from a scan instead of only copying its triangles: planes, cylinders, cones and fillets are fitted onto the mesh, and where that holds you get faces with dimensions you can measure in CAD. Simple parts go through completely – a scanned block comes out as six faces instead of thousands of triangles. Where it does not hold, you still get the faceted solid. Beta, with the deviation measured and stated either way.
- New: New at stl2step: 3D scans and freeform meshes now get a STEP file too – marked as beta. Such a mesh has no flat faces to reconstruct exact cylinders or fillets from, so you get a faceted solid instead: useful as a reference body, for boolean operations and for remodelling, with the measured deviation stated as always.
- Improved: You now always get your STEP file at stl2step - even when the check finds the solid does not match your mesh closely enough. The measured deviation stands right next to the download, with a clear note to look at the file in CAD before you machine from it: whether that spot matters for your part is your call, not ours.
- New: New: the 3D view on the stl2step page has a fullscreen button, and mouse and trackpad behave exactly as they do in the G-code viewer - including your chosen navigation mode.
- Improved: The stl2step page now works properly on a phone: the 3D view fits the screen, the boxes line up, and the little info notes open on a tap instead of needing a mouse.
- New: New: AI assistants can now do the whole STL-to-STEP job through the MCP server - upload the mesh, get a solid back with the measured deviation, and fetch the STEP file plus its DXF contour for one credit.
- Fixed: Fixed: on some parts the outer contour and a shallow pocket were missing from the program - only the holes came out. Both are back: the contour body is now measured against itself instead of the stock, and a pocket counts as a pocket from 0.2 mm deep instead of 1 mm.
- New: New: leave the cutter diameter out and step2gcode picks it from your part - the largest whole millimetre that still fits through the smallest hole. A 3.5 mm hole gives a 3 mm cutter, a 2.8 mm hole a 2 mm one. Available over the API and the MCP server.
- Improved: Tidier: the STL-to-STEP page now leads with one sentence and four keywords instead of three paragraphs — the details are one hover away. Its footer matches the main site, and the news button has moved down to the links on both pages.
- New: You can now see the reconstructed solid itself, not just the mesh you uploaded: switch between mesh, solid and both. In "both" your mesh lies over the solid as a translucent skin — wherever it shows through, the two differ.
- Improved: STL to STEP now reconstructs more parts. Where an edge cannot be represented exactly, the closest curve is used instead of refusing the whole file — and the result says how far off it is, in millimetres, next to the download.
6 September 2026
- Improved: STL to STEP now handles more parts: where two surfaces graze each other, an edge could not always be described exactly and the whole file was refused – for deviations of a thousandth of a millimetre. Such an edge is now accepted and the deviation is stated with the result, so you can judge it yourself.
5 September 2026
- New: New: turn an STL or 3MF back into a STEP file. Upload an STL or 3MF mesh and get a real solid back – holes regain their diameter, chamfers their angle, fillets their radius. How closely the result matches your mesh is stated in millimetres, right next to the download, so you can judge it yourself. For flat 2.5D parts the contour comes along as a DXF, which makes the part editable again in CAD. You will find it as "STL to STEP" in the footer. The download counts as one model, just like in the G-code generator – STEP and DXF together count once.
- New: Ratings are public now: the start page shows the average of all ratings and the comments users released for publication.
- Improved: The public ratings now also appear at the bottom of the credits window — average, number and the latest comments, right where you decide.
- Improved: Reworked rating dialog: shorter, and you can now decide whether your comment may be published.
30 August 2026
- New: First purchase bonus: your first purchase on an access token comes with extra credits at the same price – 5 models for €4.90 instead of 3, or 15 for €9.90 instead of 10.
- New: New credit packages: 3 models for €4.90, 10 for €9.90, 30 for €19.90 and 100 for €49.90, all including VAT. Credits you already bought keep their value and stay usable exactly as before.
- New: Try step2gcode straight from your AI assistant: it can now set up its own trial connection – no account, no key, nothing to install. Upload, G-code generation and the tool path preview all work on it; only the finished program needs credits, and they can be bought right from that conversation.
- Improved: Credits bought from 30 August 2026 stay valid until 31 December of the third year after the purchase, and every new purchase extends the whole balance. The remaining validity is shown next to your balance. Credits bought before that date keep their unlimited validity.
28 August 2026
- Fixed: Clearer message when arranging parts: if one of your parts is a real 3D model, the nesting view now says so by name and explains why it cannot be milled in 2.5D – instead of the cryptic “could not read part geometry” it showed before.
27 August 2026
- New: If a model is rejected because it contains real 3D shapes, you can now hand that file to us to help build 3D support. Entirely optional, and only if you confirm it: we use it purely in-house for development, without your IP address or access token, and you get a code to have it deleted again any time.
26 August 2026
- New: New: step2gcode works inside AI assistants. The MCP server lets an assistant upload your STEP, DXF or SVG file, generate the G-code and show you the tool path as an image before you download it. Setup takes one line - see the MCP page.
- Improved: Free quota adjusted: one model per calendar month is now free instead of three, with every feature included as before. What counts is still the model, not the number of attempts – you can re-generate and download the same part as often as you like with different settings, and a model you paid for stays free permanently.
23 July 2026
- Improved: Better on phones: the "What's New" badge no longer overlaps the title, and while a file is loaded, a generate button stays visible at the bottom edge – no more scrolling to start the job.
- New: New guide "Convert a STEP file to G-code: step by step" in the knowledge base: from CAD export to ready-to-run milling program, including common pitfalls.
- Improved: The diff viewer page now explains what the comparison detects and answers the most common questions – including: your G-code files are compared directly in the browser and are never uploaded.
22 July 2026
- Fixed: V-shape Adaptive now also works when arranging multiple parts (nesting): each part is properly V-carved – previously the contours were only traced along their edges.
- Fixed: Laser contour selection fixed for circles: inner circular contours are now correctly detected as inner contours – "Outer only" no longer cuts them, and kerf compensation offsets them to the correct side.
- New: New contour selection for V-shape Adaptive: choose whether to carve inner contours only, outer contours only, or all contours.
15 July 2026
- New: Six new knowledge articles answer the most common questions: What is G-code? Is an online generator safe? Which dialect for GRBL, Mach3 or LinuxCNC? What happens to my file? What does it cost? Plus: the simple Fusion 360 alternative for 2.5D parts.
- New: New knowledge article "Nesting: machine multiple parts from one sheet" — how to arrange several parts on one sheet, save material and generate a single G-code job, including practical tips on part spacing and holding tabs.
- New: Knowledge articles now show who wrote them: each article ends with a short author profile of the mechanical engineer behind step2gcode.
- New: New: "Like a slicer, but for router and laser" — the start page now explains what makes step2gcode different from classic CAM: fewer manual clicks, fewer surprises at the machine, no CAM expertise required.
- Improved: The privacy note at the upload field now states clearly: your file is only used to generate the G-code and deleted after 24 hours at the latest — no analysis, no sharing.
- Improved: Imprint and privacy policy have been updated and completed (hosting provider, supervisory authority, retention periods, third-country transfers).
9 July 2026
- New: New: Milling know-how! Compact best-practice guides under /wissen: chamfering with a V-bit (rough out first, then chamfer), setting holding tabs, choosing the workpiece origin, understanding feeds and speeds, and picking the right file format (STEP/DXF/SVG).
21 June 2026
- New: New: In “Arrange multiple parts” all parts are cut to one uniform depth by default — pre-filled with the thickness of the thickest part (one shared plate). Turn the switch off to let STEP parts keep their own native depth from the 3D model.
- New: New: Pockets now work in “Arrange multiple parts” for STEP parts. If your layout contains STEP files, their pockets, holes and inner contours are machined natively — each STEP part keeps its own depth from the 3D model, while DXF/SVG parts stay 2D at the depth you set.
- Fixed: Fixed: Parts whose outline is made of many separate strokes (e.g. a tree shape) are now recognised correctly when arranging — previously only a thin sliver was used, which looked wrong in the preview and caused parts to overlap. The full silhouette is now reconstructed.
- Improved: Improved: The XY view is now a true top-down view. Depth passes that are identical in XY (step-downs) are shown as a single line instead of several overlapping lines. As soon as you rotate the view, the full depth (all paths) comes back automatically. The 3D/XZ/YZ views still show the full depth.
- Fixed: Fixed: For parts whose outline is drawn as many separate strokes (e.g. a tree shape), the outline is now reconstructed to better than 0.05 mm (previously ~1 mm). Holes/drills no longer appear slightly off-centre relative to the part outline — arrangement, preview and toolpath now share the same reference.
- Fixed: Fixed: A DXF that contains several separate bodies is now arranged correctly — previously only the largest body was considered, so the others could overlap their neighbours. The full outline of all bodies is now used.
- Improved: Improved: Arranging now has more time to pack the parts (60 s instead of 12 s), so fewer parts are left out with a “time limit reached” message. It runs in your browser and can be stopped anytime.
- Improved: Improved: In the viewer’s Fusion navigation mode, rotating now works with Shift + left-drag — the same rotate gesture as the default mode, just with Shift added. Middle-drag still pans.
- Fixed: Fixed: Arranging at in-between angles (e.g. 15° or 45°) now places non-rectangular parts (like a tree shape) exactly where the arrangement shows them. Previously they could be milled tens of millimetres off and overlap their neighbours; only 0°/90° were correct.
- Improved: Improved: “Arrange multiple parts” no longer runs into the request limit so quickly, and the part previews no longer disappear under load. The limit was raised, lightweight preview/geometry requests are no longer counted, and the misleading “please wait an hour” message was corrected (it is only a few minutes).
- Fixed: Fixed: The milled layout now matches the arrangement exactly. Previously STEP parts could end up a few millimetres off, causing toolpaths to overlap even though the arranged parts did not. Parts are now anchored by their centre, so the result lines up with the preview.
- Improved: Improved: In the preview, STEP parts now show their real contours (outline plus inner contours, holes and pockets) instead of just the outer silhouette — so no information is missing.
- Fixed: Fixed: In “Arrange multiple parts”, a STEP part that had been generated individually before could be machined from the wrong internal file — leading to missing pockets and wrong cutter compensation. The original part file is now always used.
- Fixed: Fixed: A STEP-only layout no longer asks for a cut depth. STEP parts bring their own depth from the 3D model, so the depth is now optional (use the uniform-depth switch if you want one depth for everything). Layouts that also contain DXF/SVG still require a depth.
- Fixed: Fixed: Arranging parts with 45°/15° rotation no longer switches to 2D direct mode by mistake. Rotated parts placed side by side are no longer misread as overlapping, so extrusion stays active as expected.
- Fixed: Fixed: On iPhone/iPad you can now select files in “Arrange multiple parts”. The file picker there uses the same settings as the main upload, so DXF/STEP/SVG files are no longer greyed out on iOS.
- Fixed: Fixed: Holding tabs are no longer lost when leaving the 2D direct mode. In direct mode holding tabs aren’t technically possible and are switched off — but as soon as you return to the normal mode, your holding tabs (and other settings) are automatically restored instead of staying off.
- Improved: Improved: Easier to use with the keyboard — clearly visible focus highlights across the whole page, larger click/tap targets in “Arrange multiple parts”, and reduced animations if your system requests it.
19 June 2026
- New: New: Arrange multiple parts! Upload several DXF/SVG parts, set quantities and a sheet size, and let the app arrange them space-efficiently on the sheet — with optional 90° rotation and spacing — to save material. The combined layout is then cut/milled in one job.
13 June 2026
- New: New: SVG import! Upload SVG vector graphics (logos, lettering, artwork) directly. SVGs are converted to clean contours and work for contour milling, pockets, engraving, V-carving and laser. Real units (mm/cm/in) from the file are used automatically; unitless SVGs are read as millimeters.
- New: New: SVG scale & size control. Adjust an SVG right after upload via a scale factor or a target width/height in mm – the preview updates instantly so you can verify the size before machining.
24 May 2026
- Improved: Improved: In contact forms, your email address is now optional and clearly marked as optional for replies.
19 May 2026
- Fixed: Fixed: DXF inner contours with spline shapes are now detected and milled reliably again.
- Fixed: Fixed: Holes with a chamfer or fillet at the entry are now correctly detected and milled as helix holes.
- Improved: Improved: The interface received a visual refresh with a cleaner accent palette, reduced visual noise, and improved readability across generator, viewer, and admin views.
13 May 2026
- Improved: Improved: DXF error messages now clearly tell you when a file is empty and show a direct quick fix for missing cutting depth.
11 May 2026
- Fixed: Fixed: Openings that transition into deeper opposite-side pockets are now milled correctly as inner contours, while raised ribs are no longer mistaken for inner cuts.
10 May 2026
- Fixed: Fixed: Inner contours inside pockets are now generated continuously and no longer interrupted by unintended holding-tab paths.
9 May 2026
- Improved: Now using the latest FreeCAD 1.1.1 engine for G-Code generation.
- Fixed: Fixed: DXF files exported as 3D toolpaths are now detected early and show a clear hint to export 2D closed contours instead.
- Improved: Improved: Your settings are now only stored if you explicitly allow it. You can decline and continue without persistent local storage.
- Fixed: Fixed: Rapid travel is now safety-checked so Z retracts first before XY moves in critical cases.
- Fixed: Fixed: Empty placeholder operations without real cutting moves are now removed automatically.
25 March 2026
- New: Contour selection for laser cutting: Choose which contours to cut — all, only outer (border), or only inner (letters/holes). The system automatically detects nesting levels.
- Improved: Kerf compensation is now automatically enabled in cut mode and disabled in engrave mode.
- Improved: Kerf settings are now hidden in engrave mode — engraving traces directly on the line without offset.
- Improved: Contour selection (all/outer/inner) is now also available in engrave mode — not just for cutting.
- Fixed: The coordinate origin now stays the same regardless of contour selection. You can cut outer contours and engrave inner ones without re-zeroing your machine.
- Fixed: Viewer improvements: Laser mode now defaults to top-down (XY) view. Fullscreen no longer resets the view. Rotation direction unified. Fit-to-view fixed.
24 March 2026
- New: Laser mode now adapts to your machine! Enter your laser power in watts and the material presets automatically scale speed, power and passes accordingly.
- Improved: Kerf compensation is now a simple on/off toggle with a material-based default value. Enable it with one click — fine-tune the value if needed.
- New: New landing page for CNC milling at /mill — reach the milling mode directly via link.
23 March 2026
- New: Laser mode now has material presets! Select your material (wood, plywood, acrylic, leather, paper, fabric) and the laser parameters are set automatically for cutting or engraving.
- Fixed: Fixed: Kerf compensation now accepts decimal values (e.g. 0.15mm) without errors.
- Fixed: Fixed: The DXF contour overlay in the viewer now aligns correctly with kerf-compensated G-Code paths.
- Fixed: Laser mode now automatically selects GRBL as the only supported postprocessor.
23 March 2026
- New: New: Laser mode! Generate G-Code for laser cutting & engraving directly from DXF files. Supports GRBL with M4 dynamic power, adjustable power/speed/passes.
- New: New: Kerf compensation for laser cutting. Automatically detects inner/outer contours and offsets paths by half the kerf width for precise cuts.
15 March 2026
- New: New: You can now report bugs directly from the Diff Viewer using the report button in the toolbar.
- Improved: Improved: The Diff Viewer now tracks visitor statistics, visible in the admin dashboard.
14 March 2026
- New: New: Visual G-Code Diff Viewer – compare two G-Code files side by side with color-coded toolpath overlay. Available at /diff.
- New: New: Fusion 360 navigation mode in the 3D viewer – switchable between Default and Fusion style. Supports mouse and MacBook trackpad (2-finger pan, Shift+2-finger rotate, pinch zoom).
12 March 2026
- Fixed: Fixed: Inner contours within stepped pockets now cut to the correct depth (pocket floor) instead of going too deep through the entire workpiece.
- Fixed: Fixed: Auto-rotation now correctly detects features on side faces. Models with pockets only on non-top faces (e.g. long bars) are now oriented correctly for machining.
- Fixed: Fixed: Holes that could not be milled using the helix method (e.g. after auto-rotation) are now automatically processed using an alternative profile strategy. Previously, these holes were silently skipped.
- Fixed: Fixed: Hole milling now uses correct tool compensation. Previously, large holes were milled oversized because the tool radius offset was missing.
- Fixed: Fixed: V-Shape Adaptive now correctly processes DXF text files (e.g. lettering). Previously, many letter contours were lost due to poor segment chaining, and Z-rotation was not applied.
- Improved: Improved: The DXF preview in the viewer now shows contours with the correct rotation and origin – matching the generated G-code.
- Improved: Improved: Direction arrows are now automatically hidden when you hide the toolpath. The arrow button is disabled while the toolpath is hidden.
11 March 2026
- Fixed: Fixed: DXF files can now be rotated around the Z-axis in Direct Mode. Previously, Z-rotation was ignored.
- Fixed: Fixed: Stepped pockets (ring-shaped cavities with an inner ledge) now have their step walls correctly profiled.
- Fixed: Fixed: All holes are now correctly detected when the model is flipped 180° (previously some holes were missed).
8 March 2026
- Fixed: Fixed: Pockets are now correctly detected when flipping a model 180° to machine the opposite side.
- Fixed: Fixed: Large bores now stop at the correct depth instead of drilling all the way through the part.
- Fixed: Fixed: Pockets on stepped surfaces (e.g. counterbores) are now correctly machined instead of being skipped.
6 March 2026
- Fixed: Fixed: The ramp entry no longer starts unnecessarily high above the workpiece. Approach height is now always a few millimeters above the surface.
- Fixed: Fixed: Pockets on the underside of the model are no longer incorrectly generated when the part is flipped for machining.
5 March 2026
- Improved: Open pockets now extend the milling path beyond the workpiece edge (like facing) for clean cuts at open sides.
- Improved: Improved blind hole detection: larger holes (Ø ≥ 10mm) with moderate depth are now correctly recognized as drill holes instead of pockets.
4 March 2026
- Fixed: Pockets with large arcs in the contour (e.g. curved edges) now follow the actual shape instead of being milled as a rectangle.
- Fixed: Blind holes (bores that don't go all the way through the part) are now detected and machined as helix operations.
- New: New: Facing overshoot – the cutter now extends beyond the workpiece edge during face milling to ensure a clean surface. Enabled by default (half the cutter diameter), adjustable in settings.
- Improved: Facing follows the actual workpiece contour instead of milling a rectangle – fewer unnecessary tool moves on round or irregular parts.
21 February 2026
- Improved: Direction arrows in the 3D viewer can now be toggled on/off. Arrows are smaller and use distinct colors for better visibility.
- Improved: Impressum, Privacy Policy, and Terms of Service are now available on dedicated pages (/impressum, /datenschutz, /agb).
- Improved: Fonts are now loaded locally for faster page loads and improved privacy – no more external requests to Google.
20 February 2026
- Improved: Cleaner operation switching – activating one mode now simply deactivates the other, no more grayed-out options.
- Improved: Model mirroring (flip around X/Y axis) now works correctly with automatic face detection.
- Improved: V-Shape Adaptive now maintains contour edges precisely – no unwanted chamfer at the boundaries.
19 February 2026
- New: New: V-Shape Adaptive mode – carve detailed V-shaped grooves into DXF contours using a V-Bit.
- New: Complex DXF files (e.g. text with many curves) are now processed automatically in seconds instead of timing out.
- Improved: Chamfer, Engraving, and V-Shape Adaptive are now clearly organized – only one can be active at a time.